Launch Event, 2023-04-22

by Bill Claybaugh, RRS.ORG


Editor’s Note:

RRS member, Bill Claybaugh, built and launched his second 6-inch rocket from the RRS Mojave Test Area on Saturday, April 22, 2023. Target apogee was 69,000 feet. Winds were very low that day. Jim Gross was the pyrotechnic operator in charge for the launch event. Dimitri Timohovich and Rushd Julfiker assisted with the efforts. Bill launched from a 24-foot aluminum channel type launch rail using a pair of belly-bands that disconnected from the vehicle after clearing the end of the rail. The following is Bill’s update report on the flight as of July 1, 2023.


Flight 2 – Six Inch Rocket

Fight II Flight Report

Introduction

Something fairly violent happen to this vehicle at about 3.4 seconds into flight: onboard data and ground video indicate the rocket pitched at least 30 degrees while traveling at about Mach 2.2 at around 4100 feet above ground level (AGL).

Recovered hardware indicates the vehicle broke up under these conditions.  The parachute compartment, which was attached to the top of the motor by four ¼-20 fasteners, was torn away by fracture at all four fasteners (the fasteners remained attached to the motor). The payload, which was attached to the parachute compartment via four 0.250” diameter pneumatic separation system pins, remained attached—indeed, it was recovered with the separation system still functional and still latched to the top of the parachute compartment.

Bill Claybaugh with his second 6-inch rocket before launch.

Video shows a sudden pitch at about 3.4 seconds after first vehicle motion.  The onboard data (which records the initial part of the breakup because the computer was located in the payload section) shows that the gyro tilt went from about 5 degrees to 50 degrees over 0.08 seconds.  Measured longitudinal acceleration went from the previous around 26 g’s to 34 g’s in 0.05 seconds, and after returning to around 24 g’s for 0.15 seconds, to -12.7 g’s (the sensor floor) for 0.03 seconds, before recovering to -9 g’s for 0.01 seconds followed by loss of power. (See Chart 1.)

Chart 1: Acceleration and Tilt

Video shows the vehicle recovering from this pitch maneuver and continuing on a near vertical ascent though burnout at a video-based about nine seconds after first motion.

Flight

Following failure of the AlClO (Aluminum / Potassium Perchlorate) based head end initiator to successfully ignite the rocket (AlClO based initiators have had this issue previously, AlClO appears to be too energetic for this application, tending to blow the secondary ignition materials out the back of the rocket and on to the ground rather than igniting the grain) a jury-rigged rear end ignitor was substituted and the rocket successfully lifted off about 0.25 seconds after flames first appeared around the vehicle base.

Onboard data shows the vehicle ascending at about 88 degrees from horizontal to about 50 feet altitude when a lazy “S” turn (first to the northeast, then back to the southwest) is visible in the video and data. This turn starts about the time the belly-bands can be seen on video falling away from the vehicle.

Following this maneuver, the vehicle returns to near vertical flight to the Southwest, turning, with perturbations, from about 88 degrees tilt to an 86-degree gyro tilt over the next two-plus seconds.  Acceleration steadily builds from an initial 18.6 g’s to a maximum of 27.3 g’s at 2.53 seconds; this acceleration broadly follows the curve expected from the combination of the thrust curve, drag, and the lessening weight of the vehicle as propellant is consumed, however, the measured acceleration is much higher than expected based on static tests and flight simulations.

Telemetry reported Loss of Signal (LOS) at 2.7 seconds and at an (accelerometer-based) 2313 feet altitude and 2440 ft/sec velocity.

Measured onboard acceleration suddenly jumps from a base around 26.5 g’s at 3.18 seconds to 32.8 g’s at 3.21 seconds; measured onboard acceleration stays above 30g’g for the next 0.06 seconds, peaking at 34.7 g’s at 3.21 seconds and followed by a return to around 24 g’s for 0.15 seconds and a sudden drop to -12.7 g’s (the sensor floor) from 3.42 to 3.44 seconds and a final reading of -9.3 g’s followed by loss of power to the on-board computer.

Onboard data shows the gyro tilt angle moving from around 5 degrees at 3.37 seconds to 50.6 degrees at 3.45 seconds, followed by loss of power.

Video over this period show the vehicle suddenly turning through an apparent (visual) 30 degrees or so before pitching back to a near vertical ascent.

Analysis

A less energetic initiator is required for this vehicle; a development program will be initiated to achieve both a more reliable and a gentler ignition in future.

Figutr 1: Recovered Nozzle

Following flight, a single sliver of graphite was found on the ground about 150 feet from the launch tower.  This piece of graphite was exactly the correct shape to fit at the very rear of the graphite throat insert where that insert blends into the titanium nozzle extension. 

Recovered nozzle hardware showed that about 1-inch of the rear of the nozzle insert was missing (see Image 1); assuming the two pieces of the insert found inside the rocket were broken by impact forces, it follows that around one inch at the rear of the insert failed prior to impact. This failure would have induced a flow discontinuity in the rocket’s exhaust which thrust vector could account for the sudden pitch at 3.4 seconds into flight. The vehicle’s return to near vertical ascent appears to be due to aerodynamic assisted dampening of the perturbation, based on the tilt data from the earlier–possibly belly-band related–slow spiral of the vehicle.

Note that the recovered nozzle shows plating of Aluminum Oxide onto the ZrO coated Titanium nozzle extension above the end of the graphite nozzle extension but not in the area originally covered by the graphite insert.  This suggests the insert was present during startup (when Aluminum Oxide would be expected to condense on the nozzle extension surface) and the loss of the about 1-inch of the bottom of the graphite nozzle insert must have occurred later.

Analysis indicates that thermal stress cannot have been the cause of the loss of the back of the nozzle insert: maximum thermal stress occurs at the throat and reaches no more than 60% of the tensile strength of the graphite.  Careful measurement shows that the break occurred at the location of the joint between the titanium nozzle extension and the aluminum nozzle support structure, it thus appears that a (possibly heating related) stress concentration at that location was the probable cause of the graphite failure.

Loss of telemetry at 2.7 seconds appears to be a consequence of the GPS and transmitter antenna assembly failing mechanically; the flight computer was recovered with a clean break at the antenna PCB board.  This suggests the need for more robust support of these parts of the payload.

Breakup of the vehicle began about 3.41 seconds after launch.  The recovered pieces indicate separation of the parachute compartment from the motor was due to the upper part of the vehicle being pulled longitudinally forward, away from the (thrusting) rocket motor; further, the fracture pattern indicates an abrupt failure rather than a slightly slower swaging of the metal.  Based on the acceleration data indicating at least four hundredths of a second of significant negative g’s just before loss of power, coupled with gyro data showing the payload being thrown through an about 45 degree turn over the last 0.08 seconds of data, we can guess that the mechanical failure was a consequence of rather than the cause of the sudden turn of the vehicle.

Figure 2: Booster, post-impact

Actions

Development of a gentler and more consistent initiator is required; an effort focused on BKNO3/V (Potassium Nitrate with Boron held in a Viton matrix) has been started.

The vehicle nozzle has been redesigned to use a single piece titanium throat insert support structure and nozzle extension.  The angle of the joint between the graphite insert and the titanium shell has been increased to the conventional 5 degrees (the flight nozzle used a 3-degree angle that may have been too thin at the very end of the throat insert).

Heat paint testing of the Titanium nozzle extension on the flight nozzle indicated a maximum heat soak temperature of about 800° degrees Fahrenheit on the outside surface; this suggests a maximum outside wall temperature during operation of about one-half the paint-indicated heat-soaked temperature. Since these temperatures are well below the maximum working temperature of 6Al4V Titanium under these loads, the new nozzle is designed to allow for greater heating of the shell.

Analysis based on assuming a maximum Titanium temperature during operation of about 400° F indicates a maximum possible temperature of about 1140° degrees at the ZrO / Titanium interface and about 2800 °F at the inside surface of the Graphite insert, implying a maximum surface temperature at the nozzle throat of about 4350 °F.  A similar analysis indicates a maximum possible temperature at the inside surface of the nozzle exit of about 3300° F.

The high temperature RTV layer between the graphite insert and the ZrO layer was originally 0.005” in thickness in two sections separated by a 0.030” cork layer (a total of 0.010” of RTV); it thus should have had sufficient space, after pyrolysis of that layer, to accommodate the estimated 0.0024” thermal expansion of the Graphite Nozzle Insert.

The payload internal fiberglass support structure for the flight computer failed both at the base and at the antennae.  This structure will be redesigned in aluminum so as to provide still more robust support to the flight computer assembly.  Making this change will reduce the sensitivity of the GPS antenna and will absorb some of the transmitted energy from the telemetry antenna (the reason for going with fiberglass previously).  The effects of lower sensitivity will have to documented once that hardware is available and assembled.

The measured inflight acceleration is significantly higher than that expected from static testing and modeling of the flight trajectory; however, the burn time indicated from multiple videos is about that expected from motor modeling and the previous static test.

Analysis of the cause of the apparently higher than expected thrust has proven inconclusive.  A grain crack or void (possibly associated with the energetic AlClO initiator) would usually be expected to grow until the motor case failed.  The slightly higher than modeled initial grain area (see the report from the first flight of this vehicle for a discussion) is too small (at 0.86%) to account for the higher initial thrust (123% of the expected level). A static test motor is being prepared to try and resolve this question.

Strengthening the joint between the motor and the parachute compartment is relatively easy; additional fasteners and a thicker section to the joint should reduce the probability of a failure similar to that which occurred on this flight.  Alternatively, the motor tube could be extended by six inches to avoid having a separate parachute compartment altogether, albeit with some induced operational inconvenience when placing the initiator into the forward bulkhead.

Summary

Partial nozzle failure appears to be the main concern with this vehicle design; a secondary issue is strengthening internal components and some joints to better survive the extremely harsh conditions encountered on this flight. Finally, a cause for the apparently higher initial thrust will be sought via static testing of a new motor, which will also confirm the new nozzle design.



MTA launch event, 2021-05-29

by Dave Nordling, Reaction Research Society


The Reaction Research Society held a launch event at the Mojave Test Area mainly to support the UCLA Prometheus team for a static fire test of their high powered hybrid motor. UCLA chose one of the largest nitrous oxide hybrid motor designs, the M1575, made by Contrails Rocketry. Dave Crisalli was the pyrotechnic operator in charge for this event. I was his apprentice for the hybrid static fire.

There were three main activities at this event. The first was the UCLA Rocket Project making their preparations to launch their ethanol and LOX vehicle from the Friends of Amateur Rocketry (FAR) site from the 60-foot rail. FAR is just to the south of the RRS MTA where the UCLA Rocket Project had twice in one day static fired their 750 lbf liquid propellant rocket engine just four weeks earlier on 05-01-2021.

Weather conditions were ideal with winds being nearly still for most of the morning. This makes little difference for the hybrid motor static fire testing at the RRS MTA which was the second project by UCLA. Wind would factor heavily in the flight of the UCLA’s liquid rocket.

The third planned activity for UCLA was a series of model rocket flights from several high school teams mentored by UCLA graduate and undergraduate students. Still winds made for easier recovery of the first rockets launched that day.

UCLA Prometheus team prepares for static fire at the RRS MTA on 5-29-2021
Dave Crisalli gives the MTA safety briefing for the event in the loading area where the model rockets were assembled for flight.
UCLA graduate students conducted the model rocket launches from just west of the large test stand at the MTA

UCLA at the end of each Spring Quarter conducts a launch event where student groups build small rockets with egg payloads using single and dual-stage vehicles with model rocket class motors (G and under). UCLA graduate students and Professor Mitchell Spearrin were leading this event.

It is good experience for beginners and experts alike to build and fly model rockets., The RRS has it’s own such internal program called the Yoerg Challenge which is to motivate all members to build and fly a model rocket kit at least once from the RRS MTA. The RRS is known as an experimental society and not limited to the model rocket code, but we are also fully supportive of all forms of propulsion as long as it is safely conducted and compliant to the regulations set by the state of California.

As the UCLA hybrid rocket team was making their system checks, they discovered a problem in their nitrous filling system and valve commands. During this diagnostic period, some of the RRS members went to the nearby FAR site to see how the UCLA liquid rocket preparations were progressing.

UCLA’s liquid rocket set on the 60-foot rail launcher at FAR. The team preparing the vehicle for erecting, loading then flight.
RRS members from left to right, Bill Inman, Waldo Stakes, John Wells and Manuel Marquez, inspect the UCLA liquid rocket on the 60-foot launcher deployed at the FAR site.
A few last minute fixes and the rocket was made ready.
The liquid rocket sits on the rail before raising it for launch.
UCLA’s rocket is in position getting ready to clear the area for propellant loading and pressurization operations.

Some of the RRS members remained at the FAR site to witness the launch. After two years of design, planning, build and world pandemic, the UCLA team liquid rocket launch was an amazing success. Due to the relatively low winds that day under clear skies, recovery was made just under a mile away. Preliminary data from telemetry confirmed a new university team altitude record of 22,000 feet. It was an amazing sight to witness from the observation bunker at the RRS MTA.

UCLA’s liquid rocket had a perfect launch on 5-29-2021 setting a new altitude record of 22,000 feet by a university team. Photo by Xavier Marshall, RRS.

The UCLA Prometheus team had corrected their initial electrical problem and began the series of procedural checks to familiarize the new members of the hybrid rocket team. Some minor adjustments of the motor mount alignment was necessary before getting into test.

The UCLA Prometheus team makes some adjustments to better align the hybrid motor in the vertical skid mounted to classic I-beam at the RRS MTA.
The nitrous oxide K-bottle sits inverted in the sloped stand to allow the liquid to flow from the port. Some nitrous oxide bottles come with an internal siphon line to avoid having to invert the container. The bottle is also being chilled with ice to keep the oxidizer sufficiently dense and improve performance in hot-fire.
The top bulkhead of the hybrid motor is attached to the load cell for thrust measurement. A pressure transmitter is tapped into the nitrous oxide volume to further gauge performance.
The high-powered hybrid motor by Contrails uses four 1/4-inch fill lines and a single smaller vent line from the same floating injector at the mid-point inside
Dave Crisalli (right) inspects the hybrid motor on the test rails before the firing
UCLA Prometheus team tracks their written procedures as they progress to hot-fire in the old blockhouse.

The hybrid motor firing proceeded without further problems and resulted in a spectacular test meeting expected performance. Continuous thrust levels over 600 lbf were recorded but data analysis is still ongoing.

The hybrid motor at startup.
The UCLA hybrid motor at full thrust. Chamber pressure was over 1000 psia.

The team had a second hybrid motor grain ready for another firing so they proceeded with disassembly and inspection of the parts. The floating injector seals were still in good condition but the graphite nozzle having survived many prior hot fire tests did not survive that day’s test. Although the throat was in good condition, the inlet taper had cracked requiring a replacement the team did not have.

The top half of the floating injector with its internal siphon tube protruding up to near the top bulkhead.
The floating injector being removed from the lower half containing the spent fuel propellant grain.
The floating injector was removed after hot-fire and the dual O-ring seals were inspected. Seals were ok for re-use.
The nozzle assembly did not pass inspection after the first and only hot-fire on 05-29-2021.
The graphite nozzle fractured at the inlet taper from the first and only firing that day.

UCLA Prometheus was pleased with the results from the single firing and will proceed with integrating the motor into their flight vehicle for a launch from FAR on June 19, 2021. The RRS will hold an event at the Mojave Test Area on this same Saturday for member projects and will observe the flight from our northern vantage point.

UCLA avionics team conducted a few tests on the GPS tracking module that will fly on their vehicle in June 2021.

In the last hours of the day, after most of the UCLA liquid and hybrid teams had cleared the area, packaged and carried away their trash, packed their equipment and departed the RRS MTA and FAR sites. The UCLA avionics team remained at the MTA to conduct another series of tests on the GPS tracking system. The society was glad to support this diligence which will help assure success in one of the most important aspects of rocketry which is data acquisition from telemetry. If there is no data, it didn’t happen.

For any group interested in using the RRS MTA for their propulsion related projects, download one of our Standard Record Forms from our RRS.ORG website and submit this request to the RRS president. The society has had a long relationship with UCLA and USC, but we are also supportive to any amateur, professional or academic groups wanting to learn from test.

president@rrs.org


October 2018 meeting

The RRS met for our monthly meeting on Friday, October 12, 2018, at the Ken Nakaoka Community Center in Gardena. As usual, we got started by calling the meeting to order and reading the treasury report. We had a big agenda but covered most of the topics.

[X1]
Richard Garcia wasn’t able to join us at the October meeting. He wanted to report that he has made some design improvements to the RRS standard liquid rocket. He’s finished upgrading his engine design code to be able to analyze a blowdown engine (pressure-fed from the tanks). He also will soon have drawings for a thrust chamber design.

With some luck, I hope he’ll be back into testing at the MTA sometime soon next year.

[X2]
Electro Tech Machining (ETM) in Long Beach, California, specializes in graphite stock, graphite parts and Electrical Discharge Machining (EDM). They are experts and have been a loyal supporter of amateur rocketry groups such as UCLA and USC. The Reaction Research Society is happy to endorse them as they have been a great support to our society member’s projects as well.

Electro Tech Machining – Long Beach, contact information

Contact Cathy Braunsdorf at Electro Tech Machining.

Electro Tech Machining
2000 W. Gaylord Avenue
Long Beach, CA, 90813
(562) 436-9281

Electro Tech Machining in Long Beach, the graphite specialists

Electrical Discharge Machining (EDM) – Wikipedia article

I stopped in this week to pick up some round stock for making more graphite nozzle pucks for the ballastic evaluation motor (BEM) that is nearing completion. Graphite makes an excellent high temperature material for nozzle throats or any low ablation surfaces. We have used graphite inserts into reclaimed alpha and beta nozzles over the years at the RRS. Our society members have used graphite throats in their larger solid motor tested at the RRS MTA back in June 2018.

Plastic nozzle puck used for scale against the graphite round stock acquired by the RRS from Electro Tech Machining in Long Beach, CA

Moving into the meeting agenda, we shifted the order a little, but I have kept the numbering the same:

[1]
The latest educational event at Weigand Elementary school in Watts is going very well. The LAPD CSP program continues to help sponsor the event and we get great excitement from the kids. This Friday was the fifth of six educational events where they get to assemble the empty rockets. Osvaldo, Larry and Frank were on hand to help with the build process. The kids are really enjoying the process of learning and painting the team rockets will done in the last session before going out to launch at the RRS’s private testing site, the Mojave Test Area (MTA).

Two of our young participants show their assembled RRS alpha rocket at Weigand Elementary, Frank Miuccio in the background at the right

[2]
The next launch event at the RRS MTA will be the final step in the RRS’s educational program for Weigand Elementary school. We have this scheduled for October 27th and we hope to have cooler weather than in prior events now that the summer has passed. We have nine alphas from Weigand Elementary and three more alphas from our new membership, Wilbur Owens, Xavier Marshall and Michael Lunny.

Xavier Marshall looks over his first RRS alpha, welcome to the club!

[3]
I gave my quarterly briefing on the SuperDosa project at the October meeting. This time, I organized my thoughts and ideas into a presentation to give the RRS a general overview of the project and where we are so far.

Largely, I wanted to reiterate the project’s overall goals to many of the new members who have joined the RRS since the project’s inception in January 2017. The RRS intends to retake the amateur rocketry altitude record and in the process reopen our ability to make larger solid rocket motors and expand our reach both in our own community and literally with payloads ultimately flying above the atmosphere.

SuperDosa quarterly report, Oct-2018

I also acknowledged the recent progress of some of our new members formerly of the Chaminade Rocketry Club. Also, USC had a launch attempt with their Traveller III rocket, part of their Spaceshot Initiative. Unfortunately, instrumentation was not functioning but the flight looked to be nearly perfect. I hope USC will come present their recent accomplishments at a future RRS meeting.

Materials acquisition and some discussion about how to proceed with the propellant burn rate testing were the highlights of the discussion. More progress needs to be made in a few areas for completing the first prototype:

(a) Complete the design of all parts for the first prototype (6-inch booster)

(b) Begin prototyping instrumented dart payloads to practice flying and recovering these while getting good data. Making these devices work under the tight and unforgiving conditions that they must.

(c) More work in parachute recovery

(d) Estimating friction heat loads and heat mitigation strategies for the payload

Much of this prototyping work can be done at the MTA by flying smaller subscale vehicles and testing subsystems to prove they can work. More importantly, these tests give the society practice for the large vehicle testing which will reclaim the altitude record for the RRS.

The response to the SuperDosa project’s progress was very constructive and many new ideas were offered. I’m thankful to Frank, Steve Majdali, Larry, Osvaldo, Bill Behenna, Drew and Xavier for their inputs. I have taken notes and given actions to other members who are willing to help advance key areas of the project. Unfortunately, this topic was to be the last of the evening as my presentation easily exceeded the 20 minutes I intended.

The next quarterly report for the SuperDosa project will be January 11, 2019, and I hope to report a great deal of progress.

[4]
We had a last minute addition to the agenda, with Steve Majdali talking about black powder rockets and some very nice black powder rocket making tools he acquired while on travel. Black powder rockets are a classic form of amateur rocketry and involve many techniques that are broadly useful in other areas such as composite grain motors.

Steve Majdali shows the RRS his metal spindle for a cored grain type of 3-inch black powder rocket

Steve gave us a lot of great information specific to black powder making, pressing and a wealth of other practical information. Based on this new avenue of research, I felt the RRS would benefit more if Steve discussed this topic in more length in a stand-alone article soon to be published here on the RRS.ORG website.

[5]
The RRS has been in contact with the Additive Rocket Corporation (ARC) of San Diego. They are a startup company in San Diego with the goal of making high performance rocket motors using their novel design methodologies and 3D metal printing equipment. Discussions are still underway and thus there wasn’t much to tell. ARC was an exhibitor at the 75th anniversary symposium this year in April.

Additive Rocket Corporation (ARC) of San Diego at the 75th anniversary RRS symposium

[6]
In my discussions with ARC, they were kind enough to offer to 3D print a simple small liquid rocket chamber I designed. Prices are not cheap, but this futuristic manufacturing technique offers a great deal of complexity that is not easily nor cheaply replicated by traditional means. I have been in discussions with ARC and hope to have more to present at the next RRS meeting.

125 lbf thrust chamber design, uncooled; prototype for the RRS standard liquid project

[7]
Alastair Martin could not join us at October’s meeting. I was going to have him discuss the current topics of interest at the recent 21st Annual Mars Society Convention held this summer. Alastair is very involved with the Mars Society and the RRS.

Alastair will be at the November RRS meeting so we’ll put this topic on the next agenda.

[8]
New RRS members, Wilbur Owens and Xavier Marshall, are active with the Experimental Aircraft Association, chapter #96, at the Compton Airport in the Los Angeles area. EAA-96 is a like-minded group of enthusiasts centered on experimental aircraft. The EAA-96 has hangar space and a range of machining tools offered to their members.

Experimental Aircraft Association, Spirit of 96

Xavier had mentioned at the last meeting that the EAA would love to host a visit by the RRS. Accepting the EAA’s invitation, the RRS has scheduled a visit to the EAA in Compton on November 3rd at 10:00AM. The EAA will give an hour tour of their facilities and projects. We hope to foster a strong relationship between the EAA and the RRS.

Talk with Xavier Marshall, Wilbur Owens, the RRS president, vice president or secretary for details.

Experimental Aircraft Association (EAA) hangar
1017 W. Alondra Blvd.
Compton, CA, 90220
(310) 612-2751

One of the key points of discussion at this visit will be to discuss how the RRS and EAA can help each other or participant in joint projects. The RRS is interested in using the EAA hangar facilities if they are available. Annual membership at the EAA is $40 to the EAA national society and $40 more to the local chapter at the Compton Airport. As I understand but must confirm, with EAA-96 chapter membership, RRS membership can have access to the machining tools for building rocketry parts for those of us without facilities in our own homes.

Xavier had also mentioned that hangar storage was often very cost-effective which could be a service that the RRS could use as we look to expand our shop capabilities to our membership.

EAA Chapter 96 hangar, Compton Airport

The EAA hangar is just straight east and not very far from our regular meeting location in Gardena at the Ken Nakaoka Community Center just north of Artesia Blvd. (CA-Hwy 91). The address is above.

[9]
Osvaldo’s recent successful design of an alpha parachute recovery system was not able to be covered. We may expand this topic into a fully illustrated RRS.ORG article if we can not get this topic on next month’s agenda. This has been a quiet success and definitely worthy of exhibition to our membership.

[10]
Jerry Fuller of Aerospace Corporation had indicated interest in building and testing a larger subscale prototype of his liquid-infused hybrid motor grain. Aerospace had earlier this year successfully demonstrated a smaller prototype in flight at the RRS MTA. In choosing the next larger design, he has selected a common model rocketry size (98 mm) just under 4-inches which will allow him to use commercially available rocket body parts. Jerry is active with our friends at Rocketry Organization of California (ROC).

At this time, he is still working on the design until resources can be allocated. The RRS has invited him to present his results and the new prototype he has in mind. The RRS is happy to support private groups with a testing area and a community of amateur enthusiasts happy to assist.

[11]
The RRS had discussed having a small group of our membership go out to the next ROC event which is held the 2nd Saturday of the month. Unfortunately, neither I nor Drew were able to go this month. With the Friday night rains falling on the city, it might not bode well for the event at the Lucerne Valley as they must operate on the dry lake bed.

We are looking to coming out to the November ROC event in the Lucerne Valley and hope we can bring other RRS memmbers with us. In particular, some of our members are interested in getting more practical experience through the NAR or Tripoli prefect at ROC. Moreover, some of the RRS membership is seeking experience and support as we acquire letters of recommendation for the California pyro-op licensing in rocketry.

[12]
Saturday seminars have not yet been scheduled, but the RRS is still committed to offering an extended time period for fuller discussions by invited speakers.

[+] RRS member, Jim French, is a speaker of which we would be very excited to have. Jim was a development engineer at the famed Santa Susanna Field Laboratory here in Los Angeles during the development of the reliable and powerful H-1 engine and the injector for the massive F-1 engine. Later, he worked at TRW on the reliable, hypergolic fueled, Apollo Descent engine at TRW at their San Juan Capistrano testing site (now defunct). His book, “Firing a Rocket Engine” is available on Amazon and it is a great read.

Amazon.com – James A. French, Firing a Rocket Engine

[+] Reaction Research Society founder, George James, is another speaker we have been wanting to have. His founding work with his other organization, the Rocket Research Institute (RRI) was a great topic he covered only briefly at the 75th anniversary symposium in April.

[+] Rocketdyne retiree and materials expert, John Halczuk, is another potential speaker on the subject of his extensive research of the V-2 rocket. He gave an excellent talk last year at California State University in Northridge, on history of the V-2’s development and deployment. The V-2 guided many design decisions still used in modern rocketry today in both the United States and particularly in the former Soviet Union.

We were not able to discuss this topic in detail, but more information will be forthcoming, hopefully in the form of an announcement of our first Saturday seminar at the Ken Nakaoka Community Center on a Saturday morning.

[13]
The next RRS symposium date in 2019 will be set soon. Based on the powerful success of the 2018 event, the RRS has decided to further the tradition one more year. We hope to have an even better mixture of universities, private companies and government agencies.

Date to be announced in November, the RRS will hold the 2019 symposium at the Ken Nakaoka Community Center in Gardena

There was no time to formally raise the subject, but it was decided by the council members present at the October meeting that the 2019 RRS symposium date will be formally set by an offline discussion and the date officially announced at the next RRS meeting on November 9, 2018.

[IN CLOSING]
The next meeting of the RRS will be November 9th at the Ken Nakaoka Community Center in Gardena.

We will most certainly discuss the results of the MTA launch event scheduled for Saturday, October 27, 2018. I will build the agenda starting at the end of the month. Please contact the RRS secretary for ideas and information on meeting topics.

secretary@rrs.org

As per our constitution, the RRS will hold its annual nominations of officers for the next calendar year 2019 at the November 9, 2018 meeting. Voting by the administrative membership will take place thereafter and managed by our election chairman. Results will be announced at the next meeting on December 14, 2018.

Thank you for reading.

—- —-