MTA launch event, 2021-05-01

by Dave Nordling, Reaction Research Society


The Reaction Research Society held an event at the Mojave Test Area (MTA) on May 1, 2021. Dave Crisalli was the pyrotechnic operator in charge. RRS president, Osvaldo Tarditti, was also present along with myself, It was not to be a launch event as all planned tests were static firings by the UCLA liquid rocket team and the UCLA hybrid motor team. The winds were very high that day consistently above 20 MPH and gusts above 50 MPH at times. The weather otherwise was very cooperative with comfortable temperatures.

Other than gusting and persistently hugh winds, it was a great day at the MTA on 5/1/2021

Dave Crisalli gave a safety briefing in the George Dosa building to all attendees before the first static fire campaign would begin. The RRS pyrotechnic operator in charge is responsible for the safety of all during the event. Hazard identification (spiders, snakes, sharp objects) and good practices (hydration, sunscreen) are always part of the briefing, One of the most important things, Dave Crisalli mentioned was not to be in a hurry. It is very important to take the proper time to do things correctly and safely even if it means not proceeding with the intended test that day. Taking your time means avoiding mistakes and improving your chances for success.

Xavier Marshall observes the UCLA hybrid motor controls setup at the RRS MTA on 5/1/2021.

RRS members, Bill Inman and John Wells came to the MTA for the event, but only as spectators. The Solar Cat project is still active and undergoing improvements to its sun tracking method. Bill is also expanding the collector area and adjusting the necessary support structures. It is likely Bill and John will be back for the next RRS MTA event.

Dave Crisalli (left) and Bill Inman (right) at the RRS MTA vertical test stand on 5/1/2021

Also in attendance was the Compton Comet team who have all recently joined the society as members. It was their first time visiting the MTA and getting a chance to see another university team conduct liquid rocket test operations at our vertical test stand.

Members of the Compton Comet team, Manuel Marquez, Aarington Mitchell, Tre Willingham (from left to right) wait at the Observation Bunker at the MTA for the hybrid motor firing with Waldo Stakes (at right).

RRS member, Wolfram Blume came by the RRS MTA to take measurements of the vertical test stand for a future static fire test of his ramjet upper stage engine. He intends to use a leaf-blower compressor motor to simulate foward air flow, but a lot of calculations and planning is required before proceeding. The vertical test stand has a winch and pulley system still attached from Richard Garcia’s liquid motor test in 2017. It should be adequate for Wolfram’s lifting needs when mounting the test equipment to the stand.

The vertical test stand with the winch and pulley system still mounted.

The UCLA team spent the night before on our site setting up their equipment. This advanced planning paid off as they were ready for the first of two hot-fires of the liquid rocket just past noon.

Camera adjustments made before the first hot fire of the UCLA liquid rocket on 5/1/2021

Often, it can take several hours to verify all systems are in good working order before testing especially with a liquid rocket, The hybrid rocket was no exception that day.

The UCLA hybrid motor team installs the fuel grain and nozzle into the 98mm standard motor casing,
The UCLA hybrid motor mounted for static fire on the RRS MTA I-beam

One of the two load cells had failed so the two teams had to share the same load cell between the hybrid motor and liquid motor firings. UCLA chose to let the hybrid team go next after successful results were seen with the first firing, The UCLA hybrid motor team corrected a few issues and were able conduct a successful hot-fire by late afternoon.

The society members in attendance also had time to make some minor repairs to the new mobile trailer asset, A steel plate was added to keep intruders from entering. Thanks to Waldo Stakes for doing the welding for this temporary fix.

The mobile trailer at the RRS MTA needs a lot of repairs

There was sufficient daylight remaining for a second hot-fire of the UCLA liquid rocket, The team had another engine with the previous injector design from last built and ready with a fresh internal ablative liner. They had retanked another load of ethanol and the liquid oxygen cylinder had sufficient stores for another loading cycle.

Preparing for liquid oxygen transfer to the propellant tank

Thanks to the hard-won, acquired experience of the UCLA team and their commitment to training new members and holding to their proven procedures, they were able to conduct the second firing safely for an impressive finish that day.

The UCLA liquid rocket team poses before their liquid rocket after a second successful hot fire on the same day.

Initial data from both UCLA static firings of their liquid motor suggest that the 650 lbf nominal thrust motor outperformed expectations and will be ready for vehicle integration and flight by May 29, 2021. The UCLA team had reason to celebrate at the end of the day. The RRS was glad to be a part of UCLA’s continued campaign to fly liquid rockets that are competitive with any university team in the country.

For other universities interested in working with the RRS, please contact the society president submitting a Standard Record Form downloaded from our website,

president@rrs.org


MTA event, 2018-11-17

The Reaction Research Society (RRS) was glad to offer our Mojave Test Area (MTA) to UCLA for a series of tests of their liquid rocket. This was a private event, but Osvaldo and Elisa were there to witness a successful hot-fire series.

UCLA has been working on liquid rockets and this event was to test the improved version of their 650 lbf thrust LOX/ethanol engine. After validating minor modifications to the plumbing and an improved mechanism for their pneumatic valve actuators, UCLA expected good performance from this test with an expected burn time of 13.8 seconds and an expected total impulse of 9000 lbf-sec.

UCLA makes preparations on their liquid rocket, 11-17-2018 at the MTA

Other improvements include collecting better data. Data collection has been a challenge for many teams over the years. Tank, manifold and chamber pressure measurements were successful combined with thermocouples on the LOX lines for a better estimate of density and on the engine outer surface to anchor heat transfer assumptions. This temperature data has helped to better anchor their estimates of characteristic velocity (C*) and specific impulse (Isp). UCLA was not making direct flow rate measurements in this test, but has planned to do so in another forthcoming test.

UCLA’s liquid rocket in position

UCLA has also been giving their newer student team members opportunities on this project by passing knowledge gained from the more experienced members as turnover is a necessity with graduation.

UCLA liquid rocket hot fire way after sunset, 11-17-2018

Results from the hot-fire seemed to show that UCLA’s computational models were fairly close to actual performance. Total impulse was less than predicted at 8174 lbf-sec, average thrust at 467 lbf and peak thrust at 550 lbf, but a longer than predicted burn duration of 17.0 seconds.

These are good results but improvements can be made, particularly in getting direct propellant flow rate measurements. Both C* and Isp can be directly measured from propellant flow rate.

Further refinement of their assumptions based on this new hard data will help them in their next hot-fire planned for January 2019. The RRS is glad to assist UCLA and other universities with their liquid rocket projects at our Mojave Test Area (MTA). The RRS is ready to help UCLA take their next step in the new year.

We will surely discuss the results of this and the upcoming test of UCLA’s liquid rocket at the next RRS meeting, Friday, December 14th, 7:30pm, at the Ken Nakaoka Community Center in Gardena.

August 2018 meeting

The Reaction Research Society (RRS) held it’s monthly meeting on August 10, 2018 at the Ken Nakaoka Community Center. We were very well attended with four new people including returning member, Jim French. I was unable to attend the meeting, but other council members gave me their notes.

The RRS meeting got a late start at 8:00pm. (Our starting time is supposed to be 7:30pm.) The agenda items were not covered in order, but the list of topics to be covered were as follows:

[1]
This was to be a discussion of the 2018-07-21 launch event that the RRS held at the MTA with LAPD CSP and the student group at Watts. The event was successful with both the student alpha launches and a few RRS member alphas with payloads. The event was summarized in a previous article. A few things could have been done better which will make future events go more smoothly.

[+] A single, simpler briefing to the kids would have been more effective. The kids in the student classes do pay attention at the events (which is great) but the RRS is giving a lot of redundant information and a more concise presentation delivered by only the pyro-op will be far better than having three people talking at the same time.

[+] Also, every person conducting a launch or hot-firing at the MTA must submit a detailed proposal to the pyro-op for review at least a week in advance and gain the RRS and pyro-op’s approval PRIOR to coming to the event. The RRS used to be even more stringent on this requirement. The use of the RRS standard record form is required to be filled out by the experimenter for review by the pyro-op. The RRS requires advance preparation and there is no reason why this can not be done by all participants.

In recent times, our pyro-ops have been very casual about this requirement and have been kind enough to review things on the spot, but this was always at the pyro-op’s discretion. The pyro-op is the single and solo authority for what is and isn’t done at the launch event. The pyro-op should be the most informed individual about what is going to be attempted at the MTA.

The RRS has a Standard Record Form available on this website under the Membership tab of the Homepage and under the subheading of Forms. This downloadable document gives members a basic framework for the detailed information they must provide to the pyro-op describing their project and its goals. The RRS encourages members to present their proposed projects at the meetings and be very detailed in any reports submitted to the pyro-op and RRS president. The RRS wishes to keep good records to benefit the society and future projects.

RRS – Membership / Forms / Standard Record Form

[+] In future events where we have the student launch event conducted first, we should not plan nor conduct any events before the student launch. Getting back to an earlier point, having launch and hot-fire events declared, reviewed and scheduled days in advance will help make RRS events go more smoothly and safely. Years of experience at the MTA has shown that tasks ALWAYS take longer than planned and too much waiting can make coordination of large groups unnecessarily difficult. Therefore, having our coordinated events go off first without distractions from other planned activities will make it easier for our pyro-ops to conduct their duties and make our participants be more organized in their projects.

[+] The extreme heat of mid-July made it very difficult to conduct operations but having the motorized cart to shuttle the pyro-ops to and from the launch site made a critical difference. Bringing ice in the summer is a necessity. Having everyone well prepared for the hot weather continues to be the best advice.

[2]
Chris Kobel who is a member of Rocketry Organization of California (ROC) shared some advice for pyrotechnic operators (pyro-op). Chris has been a pyro-op for over 10 years and is pretty active with amateur rocketry. Safety was the primary emphasis of his presentation. He also mentioned a key point of contact at the Office of the State Fire Marshall (OSFM) of California, Tom Campbell. Mr. Campbell is very important authority at the California State Fire Marshall’s office who can answer important questions. Chris and the other pyro-op members at ROC were also willing to counsel RRS members interested in becoming pyro-op’s.

The RRS was glad to have Chris give our membership a wealth of information. We look forward to working more with Chris and ROC in the near future as the RRS is expanding our roster of pyro-ops for our growing events.

[3]
Osvaldo’s flight telemetry from his alpha flight on 2018-07-21 was briefly mentioned at the meeting. It was good that the flight was successful that data was taken. Given the time constraints, he’ll give more details at the next month’s meeting.

[4]
Progress on the RRS alpha parachute systems and future attempts was to be detailed by both Osvaldo and Larry who each attempted a unique recovery system built into the small confines of the alpha payload tube. Again, insufficient time was available at this meeting and this event can move to next month.

[5]
Sam Austin gave a presentation of MIT’s solid rocket launch and his upcoming liquid rocket hot-fire. Sam is here in Los Angeles for the summer on his internship, but managed to find time to launch his rocket from the FAR site on the same day the RRS held our launch event on 2018-07-21. The MIT team’s custom-built solid rocket motor (O4000) made from scratch reached an altitude of 33,132 feet as confirmed by dual altimeters. The vehicle weighed 121 lbm at liftoff and reached a peak velocity of Mach 1.8.

MIT’s rocket launch from FAR on 2018-07-21

MIT team poses with their rocket, 2018-07-21

Sam described a rough order of operations for their solid rocket grain making process and detailed their recovery. The rocket touched down safely 2 miles away and was fully recovered. The MIT team was elated and attributes their successful launch to careful design, many hours of testing that went into every component. The RRS is happy for MIT’s success and hopes they will test at the MTA with their next rocket.

[6]
There will be a liquid rocket hot fire testing on August 18th at both the Friends of Amateur Rocketry (FAR) site and the RRS MTA. Sam Austin has been working on his liquid rocket motor to test at FAR, next door to the RRS MTA site. Richard Garcia has built a small liquid motor for what could become the RRS standard liquid rocket design. Our two members have agreed to share resources and the hot fire events will take place on 2018-08-18.

Both projects will use a nitrogen K-bottle as their pressurization source and will share a liquid oxygen dewar to provide the oxidizer to both of their engines. Richard’s and Sam’s liquid rocket motors will use kerosene as a fuel. Richard’s design is a 1000-lbf thrust design with an assumed chamber pressure of 300 psig.

Sam and Richard have put a lot of work into these projects and we hope they have success. I plan to go out there to help document the event for a new posting to come shortly after.

[7]
The meeting was to discuss upcoming RRS launch events including the next one with LAPD. Frank has said that the next event with the LAPD CSP will be with the Boys and Girls Club. LAPD CSP is also working on setting up another school group in Watts for an RRS event. Specific dates were not yet set, but that information will be coming soon. We will post announcements of forthcoming launch events in the “Forum” section of this webpage.

[8]
RRS Instagram and YouTube account guidelines have been generated by RRS treasurer, Chris Lujan, and are now being reviewed by the RRS executive council. The idea of creating an RRS media manager position was proposed and accepted by the council. The RRS is considering offering this new position to RRS members, Bill Janczewski and Alastair Martin, who both have put forth a great deal of excellent work for the society. The RRS executive council will vote soon to better our social media presence to help our outreach efforts and give our followers a better view into the society.

Richard Garcia shared access information with the executive council on the existing social media accounts that the RRS has including Facebook and YouTube.

The RRS executive council now has access to Instagram and will be sharing photos from events more easily and quickly with our public audience. I have already begun to load photos I’ve had from recent events. More of the RRS will be posting to Instagram very soon.

Subjects not on the agenda included:

[BONUS 1]
The RRS will start to hold special Saturday morning seminars for special topics that can be covered in more depth outside of our monthly meeting. These bi-monthly sessions will take some work to coordinate, but should allow more of our membership to enjoy the quality of talks that we have been privileged to enjoy. Jim French agreed to give the first of the RRS Saturday seminars at a date to be determined very soon. Jim was a member of the RRS 25 years ago and we’re happy he’s come back to join us.

book by RRS member, Jim French

James R. “Jim” French also has the distinction of being a rocket engineer for over 60 years and worked at TRW on the Apollo program. He wrote a book about his experiences called “Firing a Rocket”. This first RRS Saturday seminar will be a great presentation to start this series. The date will be announced soon.

[BONUS 2]
I have been able to get the top and bottom plates made for the RRS ballistic evaluation motor (BEM) which will be a key part of the SuperDosa project and the RRS having the ability to take accurate burn rate measurements at the MTA for future motors. I am thankful to Matt Moffitt of CNC Specialty Machining in Huntington Beach. I hope to have the cylinder piece in the RRS BEM machined soon. This will likely require lathe work. Osvaldo is also looking into getting this part made. It is my hope the RRS BEM can be completed by the next quarterly update of the SuperDosa project in October 2018.

Top and bottom plates for the RRS BEM just back from the mill.

I have heard that Jack Oswald is trying to get into testing his large solid motor with an improved design. The RRS may have more to present next month on this subject.

[BONUS 3]
I wanted to bring a special device I bought from Additive Aerospace called a fly-away rail guide. I was introduced to this device by David Reese of ROC. Although the RRS has a very effective box-type rail launcher at the MTA site which will remain our standard technique, I decided to attempt a new method of launching an alpha just to get a longer guided path on launch.

Additive Aerospace – fly-away rail guides

This device allows a rocket to be fired from a extruded aluminum rail launcher such as the one we have at the RRS MTA, but without having to permanently attach the round launch buttons to the rocket itself. A spring-loaded clampshell piece goes around the rocket with a launch button on either side such that the clamp is closed when the rocket is on the rail. As the rocket takes off, the fly-away rail guide goes with the rocket along the rail launcher until the buttons clear the rail and swing open releasing it from the rocket as it speeds away.

Fly-away rail guide from Additive Aerospace; custom-built for an RRS standard alpha rocket, shown in the open position.

These devices are intended for common model rockets of the standard metric sizes (38mm, 54mm, 76mm, 98mm). I had this rail guide customized to fit an RRS standard alpha rocket which is slightly smaller than the 38mm size at 1.25 inches in diameter. I hope to demonstrate the fly-away rail guide device with a loaded RRS alpha from the 12-foot rail launcher at the RRS at the next event. I will relay my findings to the society and back to Additive Aerospace who is very interested to see how their design can work with the RRS micrograin rockets.

[IN CLOSING}

Meeting adjourned at 9:16pm which isn’t too bad. Our hosts at the Ken Nakaoka Community Center continue to graciously allow us to finish up despite the center’s closing at 9:00pm on Fridays. The RRS should seek to better finish on time as the staff at the center need to go home.

The next meeting of the RRS will be held on September 14, 2018.

For questions, contact the RRS treasurer, Chris Lujan.
treasurer@rrs.org